MotionRC FlightLine Corsair design flaw


Author: Dave
Date: 04.10.24 - 8:58pm



So the MotionRC FlightLine 1600mm F4U-1A/D Corsair retracts landing gear (SKU: FLW304082) is a pretty fragile design.

A friend has already gone through like 5 of these in 5 days of flying :(

The flaw lays in the cross pin you see sticking out of the main shaft. This pin presses against the side of the case and rotates the tire as it comes out of the body of the plane. The flaw is the pin is to large of a diameter leaving to thin of a side wall on the main shaft and it will break off very easily. The main shaft is quite a hard steel which also leaves it brittle.

Maybe this was designed as a tear away part to save the structure of the wing, not sure, but at $22 a pop, its just to fragile. I contacted support to see if just a replacement pin was available. Seems like buying these in bulk would be reasonable, but only the complete unit is for sale. They are also frequently out of stock since everyone is breaking them :(

Soooo, we are playing around with redesigning the part some. Below is the replacement we came up with. Common grade of cold rolled steel with a 1/16" roll pin. I cant see it breaking again at this spot, but will see if it shifts the damage to some other part of the plane or if its a win. I will update this post as we experiment more.

Below are some picts and dimensions. Not hard to fabricate, just a bit fussy with the small dimensions.

Also worth mentioning, if the side you need is out of stock, only the die cast block has a R/L side to it. Everything else is interchangable so you can swap pins with your broken one and get back in the game.





If you are putting one of these on a servo tester, the electronics will trigger with only a min or max signal. Then the device will operate fully until it reaches its limit switch and stops.

I might need to put a bushing around the rollpin to bring it back to the expected 3mm diameter to keep the wheel rotation correct. In practice the diameter difference of .12" vrs .0625" or .030 per side probably wont matter. Time will tell.

Unfortunately the relief on the die cast block doesnt give us any room to enlarge the hole for a larger main shaft.

You would need some 1/4 steel rod, a 2.5mm tap, metal lathe, 1/16" roll pin, calipers, and a file to make this part.




Comments: (0)

 
Leave Comment:
Name:
Email: (not shown)
Message: (Required)
Math Question: 35 + 92 = ? followed by the letter: L 



About Me
More Blogs
Main Site
Posts: (year)
2024 (1)
     MotionRC FlightLine Corsair design flaw
2023 (6)
     Boom Microscope
     Schlage FE595 Problem
     Leaf Bagger Bin
     ridiculous
     Stupid Games With Bees
     Glacier Bay Water Cooler
2022 (2)
     Truck Cap to Trailer Cover
     Match Paint
2020 (1)
     Water jug stand
2018 (1)
     ant bait
2017 (1)
     Ac Cart
2016 (2)
     Uberscoot 1000w Review
     Nokia HeadPhones Stuck
2015 (3)
     car trash
     Manual Defrag
     mc60 mod
2014 (6)
     Good Value
     RC SnowBlower
     Haier Default Temp
     VinoTemp Default Temp
     ioT Humidor
     Trash Can Wheels
2013 (2)
     Trailer Cover
     Redneck House fan
2012 (6)
     Ladder Rack
     misc hacks
     Couch Mod2
     Truck Cap Lift II
     Tub Drain
     Truck Cap Cart
2011 (4)
     Laptop Hinge Fix
     Jump Starting a lawn mower
     Portable Firepit
     Ice dams
2010 (9)
     truck box
     Lawn Sweeper Mods
     Home book binding
     Snow Blower Mod
     Reading Table
     Couch Mod
     Power Chill 12v Circuit
     PowerChill Thermostat
     RE Pythagoras Style
2009 (2)
     Icy eves
     Interwall Temperatures